Etc SineWave Power Module (DMX) Manuel d'utilisateur télécharger pdf

IES PowerModule Operators’ Manual v1.4 Isine 1

Operator Manual

Power-module

distributed dimmers

Contents:

1 Introduction ......................................................2

1.1 Product range ..........................................2

1.2 New dimmer design.................................2

1.3 Distributed dimming.................................2

1.4 Key features of itec system......................2

2 Unpacking and installation ...............................2

2.1 Unpacking & checking .............................2

2.2 Positioning...............................................2

2.3 Connections.............................................2

2.4 Safety ......................................................3

3 Control panel layout .........................................3

4 Function overview ............................................4

4.1 Forward or reverse phase operation........4

4.2 Maximum and minimum levels ................4

4.3 Response speed......................................4

4.4 Non-dim operation ...................................4

4.5 Local control ............................................4

4.6 Dimmer curves ........................................4

4.7 Status reporting .......................................4

4.8 Backup settings .......................................4

5. Information displays and manual control.........5

6 Programming....................................................6

6.1 Flow diagram ...........................................6

6.2 General Programming Advice..................6

6.3 Front Panel Controls................................6

6.4 General controls .....................................7

6.5 DMX programming ..................................7

6.6 Serial address..........................................8

6.7 Maximum & Minimum levels ....................9

6.8 Response time.........................................9

6.9 Dimmer curves ........................................9

6.10 Non-Dim operation ..............................10

6.11 Maximum current.................................10

6.12 Voltage regulation................................11

6.13 Phase-On and Phase-Off ....................12

6.14 Start Mode...........................................12

6.15 Passwords ..........................................13

6.16 Sleep mode .........................................13

6.17 Fault reporting .....................................13

6.18 Return to factory settings.....................14

7. DimSTAT.......................................................14

8. Fault finding...................................................15

8.1 Reported faults ......................................15

8.2 First line maintenance ...........................15

9. Specifications ................................................17

10. Declaration of conformity.............................19

11. Index ...........................................................20

12. Flow chart......................................... appendix

1 2 3 4 5 6 ... 20 21

Résumé du contenu

Page 1 - Power-module

IES PowerModule Operators’ Manual v1.4 Isine 1 Operator Manual Power-module distributed dimmers Contents: 1 Introduction ...

Page 2 - 2 Unpacking and installation

IES PowerModule Operators’ Manual v1.4 Isine 10 6.9 Dimmer curves Dimmer curves (dimmer laws) are used to adjust the relationship between control

Page 3 - CH 1 2 3 4 5 6 A:016*

IES PowerModule Operators’ Manual v1.4 Isine 11 The process is in three parts; setting a current limit, choosing any priority channels, and activa

Page 4 - 4 Function overview

IES PowerModule Operators’ Manual v1.4 Isine 12 VOL.REG. [ON] 5. Press Ï or Ð to set the voltage regulation function either ON or OFF (shown in sq

Page 5 - 5. Information displays and

IES PowerModule Operators’ Manual v1.4 Isine 13 6.15 Passwords Passwords are used at 3 levels of the PowerModule dimmer set-up procedure: DMX, CO

Page 6 - 6 Programming

IES PowerModule Operators’ Manual v1.4 Isine 14 6.17.1 To check fault reports and to reset the log. 1. Press CHK. Note: This screen never requi

Page 7 - 6.5 DMX programming

IES PowerModule Operators’ Manual v1.4 Isine 15 8. Fault finding 8.1 Reported faults 8.1.1 No load (control present but no output) This can be rep

Page 8 - 6.6 Serial address

IES PowerModule Operators’ Manual v1.4 Isine 16 8.2.6 Lamp filaments are noisy Replace the lamp with a new lamp, and in the case of 110V Parlamp

Page 9 - 6.8 Response time

IES PowerModule Operators’ Manual v1.3 17 10. Declaration of conformity I.E.S. B.V. DECLARATION OF CONFORMITY According

Page 10 - 6.11 Maximum current

IES PowerModule Operators’ Manual v1.3 18 11. Index Backup settings defined ...5 BASIC

Page 11 - 6.12 Voltage regulation

IES PowerModule Operators’ Manual v1.3 19 DMX control ...8 Navigation through the menus...

Page 12 - 6.14 Start Mode

IES PowerModule Operators’ Manual v1.4 Isine 2 1 Introduction 1.1 Product range This handbook describes the operation and programming for the IES

Page 13 - 6.16 Sleep mode

IES PowerModule Operators’ Manual v1.3 20 Appendix: Flowchart.

Page 14 - 7. DimSTAT

IES PowerModule Operators’ Manual v1.3 21

Page 15 - 8. Fault finding

IES PowerModule Operators’ Manual v1.4 Isine 3 2.3.5 DMX data signals All PowerModules are controlled by DMX 512 connected by a two-pair and shiel

Page 16

IES PowerModule Operators’ Manual v1.4 Isine 4 CHAS (with LED) CHASe. Provides access to the dimmer’s internal 20-pattern chase effects system for

Page 17 - I.E.S. B.V

IES PowerModule Operators’ Manual v1.4 Isine 5 5. Information displays and manual control This group of buttons provides direct access to detaile

Page 18 - 11. Index

IES PowerModule Operators’ Manual v1.4 Isine 6 CH ST SP L FADE 01 00 1,0  OFF where: CH is chase number ST is step number SP is speed (in secon

Page 19

IES PowerModule Operators’ Manual v1.4 Isine 7 relates to the number of dimmers in the PowerModule – either 2, 4 or 6. Note: A questionmark (?) a

Page 20 - Appendix: Flowchart

IES PowerModule Operators’ Manual v1.4 Isine 8 3. Press Ð or Ï to choose DMX FAIL menu. Press ENT. 4. The screen shows: GENERAL DMX FAIL [HOLD

Page 21

IES PowerModule Operators’ Manual v1.4 Isine 9 6.7 Maximum & Minimum levels It is possible to affect the output range of a dimmer by setting a

Commentaires sur ces manuels

Pas de commentaire

Etc SineWave Power Module (DMX) Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Etc SineWave Power Module (DMX). ETC SineWave Power Module (DMX) User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Etc SineWave Power Module (DMX)