Etc Unison Heritage Fader Station Manuel d'utilisateur télécharger pdf

ETC Installation Guide

Unison Heritage Fader Station

Unison Heritage Fader Station Page 1 of 4 Electronic Theatre Controls, Inc.

Corporate Headquarters



3031 Pleasant View Road, P.O. Box 620979, Middleton, Wisconsin 53562-0979 USA



Tel +608 831 4116



Fax +608 836 1736

London, UK



Unit 26-28, Victoria Industrial Estate, Victoria Road, London W3 6UU, UK



Tel +44 (0)20 8896 1000



Fax +44 (0)20 8896 2000

Rome, IT



Via Pieve Torina, 48, 00156 Rome, Italy



Tel +39 (06) 32 111 683



Fax +44 (0)20 8752 8486

Holzkirchen, DE



Ohmstrasse 3, 83607 Holzkirchen, Germany



Tel +49 (80 24) 47 00-0



Fax +49 (80 24) 47 00-3 00

Hong Kong



Rm 1801, 18/F, Tower 1 Phase 1, Enterprise Square, 9 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong



Tel +852 2799 1220

Service:

(Americas) service@etcconnect.com



(UK) service@etceurope.com



(DE) techserv-hoki@etcconnect.com



(Asia) s[email protected]

Web:

www.etcconnect.com



Product information and specifications subject to change.

7181M2150



Rev B



Released 2012-02



ETC intends this document to be provided in its entirety.

Overview

The Unison

Heritage Fader Station

connects to the LinkConnect station

communication bus. LinkConnect is based

on Echelon

LonWorks™ with LinkPower

bidirectional protocol, and uses one pair of

wires (data+, data–).

LinkPower is topology free and polarity

independent; you can install your LinkPower

data runs in any desired combination of bus,

star, loop, and home-run. ETC recommends using Belden 8471 (or approved

equal) wire. The total combined length of a LinkPower wire run may not exceed

1,640 feet (500m), with a maximum distance of 1,312 feet (400m) between any two

devices. The Heritage Fader Station may be installed into an industry standard

single gang backbox (provided by others) or a surface mounted backbox (sold

separately and available from ETC).

All control wiring should be installed and terminated by a qualified installer and

should follow standard wiring installation practices. Leave approximately 10 inches

(254mm) of wiring in the backbox for connection and to allow slack for future

service needs.

Installation

Installation should follow local codes

and standard practices. The backbox

should be installed square for best

results. Ensure that the backbox is clean

and free of obstructions and that all

wiring is installed correctly.

Heritage stations ship with a termination

kit containing a LinkPower pigtail, a

ground wire pigtail, spacers, and all

required connectors for installation.

Note:

ETC requires that all stations be grounded by using grounded

metal conduit or a 14 AWG (2.5mm

) ESD drain wire.

LinkPower

pigtail

Ground

pigtail

WAGO

Spacers

1 2 3 4

ETC Installation Guide 1

Résumé du contenu

Page 1 - ETC Installation Guide

ETC Installation GuideUnison Heritage Fader StationUnison Heritage Fader Station Page 1 of 4 Electronic Theatre Controls, Inc.Corporate Headquarters

Page 2

ETC Installation GuideUnison Heritage SeriesUnison Heritage Fader Station Page 2 of 4 Electronic Theatre Controls, Inc.Connect the WiringStep 1: Pull

Page 3

ETC Installation GuideUnison Heritage SeriesUnison Heritage Fader Station Page 3 of 4 Electronic Theatre Controls, Inc.c: Use the WAGO connector to c

Page 4

ETC Installation GuideUnison Heritage SeriesUnison Heritage Fader Station Page 4 of 4 Electronic Theatre Controls, Inc.Step 4: If required for the st

Commentaires sur ces manuels

Pas de commentaire

Etc Unison Heritage Fader Station Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Panneau de contrôle Etc Unison Heritage Fader Station. ETC Unison Heritage Fader Station User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels