Etc Unison DRd with Paradigm Control Termination Kit Manuel d'utilisateur télécharger pdf

ETC

Setup Guide

Paradigm DRd Termination Kit Installation

Paradigm DRd Termination Kit Setup Guide Page 1 of 2 Electronic Theatre Controls, Inc.

Corporate Headquarters



3031 Pleasant View Road, P.O. Box 620979, Middleton, Wisconsin 53562-0979 USA



Tel +608 831 4116



Fax +608 836 1736

London, UK



Unit 26-28, Victoria Industrial Estate, Victoria Road, London W3 6UU, UK



Tel +44 (0)20 8896 1000



Fax +44 (0)20 8896 2000

Rome, IT



Via Ennio Quirino Visconti, 11, 00193 Rome, Italy



Tel +39 (06) 32 111 683



Fax+44 (0)20 8896 2000

Holzkirchen, DE



Ohmstrasse 3, 83607 Holzkirchen, Germany



Tel +49 (80 24) 47 00-0



Fax +49 (80 24) 47 00-3 00

Hong Kong



Rm 1801, 18/F, Tower 1 Phase 1, Enterprise Square, 9 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong



Tel +852 2799 1220



Fax +852 2799 9325

Service:

(Americas) service@etcconnect.com



(UK) servic[email protected]



(DE) techserv-hoki@etcetcconnect.com.com



(Asia) service@etcasia.com

Web:

www.etcconnect.com



Product information and specifications subject to change.

7182M2230



Rev A



Released 09/2008

Overview

The Paradigm DRd termination kit (P-DRd-TK) is provided for field installation into a DRd enclosure for

use with a Paradigm architectural control processor. This kit includes the DRd left I/O board.

The left I/O board should be installed by the installing contractor or qualified field technician.

Installation

Note:

All low voltage control cables must run in separate conduit from power wires.

Note:

Data terminations to the left I/O board are specific to use with the Paradigm

architectural control processor (P-ACP) and are not compatible with an installed

SmartLink architectural control processor (S-ACP).

NO4

COM4

NO3

COM3

NO2

COM2

NO1

COM1

IN4

GND

IN3

GND

IN2

GND

IN1

GND

OUTPUTSINPUTS

J4 J5

7183B4605 REV

MADE IN THE U.S.A.

RS-232

C2 C3 C4

CR1

CR2

CR3

CR4

CR5

ETHERNET

The left I/O board supports the Paradigm architectural

control processor data terminations including:

• RS-232 on a male 9 pin (D style) connector

• Ethernet on a RJ-45 female connector

• Contact closure input terminations on a 8 pin

pluggable connector. Terminations available for 4

inputs and 4 ground wires.

• Contact closure output terminations on a 8 pin

pluggable connector. Terminations available for 4

normally open relay outputs and 4 common wires.

Step 1: Align the left I/O board to the mounting

pems on the left side of the DRd enclosure.

Step 2: Secure with the screws provided.

1 2

Setup Guide 1
ETC Setup Guide 2

Résumé du contenu

Page 1 - Setup Guide

ETC® Setup GuideParadigm DRd Termination Kit InstallationParadigm DRd Termination Kit Setup Guide Page 1 of 2 Electronic Theatre Controls, Inc.Corpora

Page 2 - ETC Setup Guide

ETC Setup GuideParadigm DRd Termination KitParadigm DRd Termination Kit Setup Guide Page 2 of 2 Electronic Theatre Controls, Inc.Connect to Serial RS-

Commentaires sur ces manuels

Pas de commentaire

Etc Unison DRd with Paradigm Control Termination Kit Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Etc Unison DRd with Paradigm Control Termination Kit. ETC Unison DRd with Paradigm Control Termination Kit User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Etc Unison DRd with Paradigm Control Termination Kit