Etc Source Four LED v1.6.0 User Manual Manuel d'utilisateur

User Manualv1.6.0Rev ASource Four LED fixtures are intended for professional use only. Read entire User Manual before using equipment.ProfileCopyright

4 Source Four LED Profile v1.6.0 User ManualApplicationsDocument ConventionsNoticesThroughout this manual, the following are used to alert you to note

Corporate Headquarters  3031 Pleasant View Road, P.O. Box 620979, Middleton, Wisconsin 53562-0979 USA  Tel +608 831 4116  Fax +608 836 1736London,

Introduction 5SafetyThe Source Four LED Profile fixtures are intended for professional use only. Read the entire User Manual before using equipment.WA

6 Source Four LED Profile v1.6.0 User ManualContactsIf you have questions about your Source Four LED Profile fixture that are not answered in this man

1 Installation and User Interface 7Chapter 1Installation and User InterfaceThis chapter contains the following sections:• Specifications. . . . . . .

8 Source Four LED Profile v1.6.0 User ManualSpecificationsPhysical• Rugged die-cast aluminum construction • Hanging yoke standard• Easy-access slots f

1 Installation and User Interface 9Typical Power ConsumptionLustr+Series 2 LustrStudio HDDaylightTungsten90V 120V 240VIdle Power / Current 4.27W / 0.0

10 Source Four LED Profile v1.6.0 User ManualNote About LED FixturesAll LED sources experience some lessening of light output and some color shift ove

1 Installation and User Interface 11HardwareBasic AssemblyFigure-1.1 Basic assembly.Mounting HardwareA yoke is available for mounting fixtures.WARNING

12 Source Four LED Profile v1.6.0 User ManualInstall Lens TubeAny of the ETC Source Four lens tubes can be installed into the shutter barrel of the So

1 Installation and User Interface 13Aim AdjustmentsThe fixture can be tilted up and down to aim the light where it is needed. The adjustment is the sa

ETC ® permits the reproduction of materials in this manual only for non-commercial purposes. All other rights are reserved by ETC.ETC intends this doc

14 Source Four LED Profile v1.6.0 User ManualFocusing the BeamFigure-1.4 Focusing the beam.Step 1: Loosen the beam focus knob located under the barrel

1 Installation and User Interface 15Soft Focus DiffuserTo clean up edge effects, use the soft focus diffuser in the A-size pattern holder. If combinin

16 Source Four LED Profile v1.6.0 User ManualStep 1: Use a Phillips screwdriver to loosen the screws on the drop-in iris slot cover. Do not remove scr

1 Installation and User Interface 17Step 1: Secure the C-clamp to the yoke with the provided yoke bolt and lock washer.Step 2: Place the C-clamp on th

18 Source Four LED Profile v1.6.0 User ManualAdjusting the Yoke PositionThe Source Four provides multi-positioning capabilities within its yoke for ov

1 Installation and User Interface 19Installation ClearancesCooling and Duty CycleSource 4 LED fixtures are fan cooled and can operate all channels at

20 Source Four LED Profile v1.6.0 User ManualDimensions and Hanging ClearancesUse the following dimensions to allow proper clearances around the fixtu

1 Installation and User Interface 21Safety CableA safety cable (or other approved safety device) should be attached to the fixture housing and wrapped

22 Source Four LED Profile v1.6.0 User ManualPower and Data Cabling RequirementsPowerThe Source 4 LED fixture operates on AC power, 100 to 240VAC/50-6

1 Installation and User Interface 23ConnectionsAll connections and user controls are located on the back of the fixture.Figure-1.13 Power and DMX Conn

Source Four LED Profile v1.6.0 User Manual iTable of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . 1Quick Setups . . . . .

24 Source Four LED Profile v1.6.0 User ManualDMX ProfileAddressingAddresses must be set between 1 and 510. Each Source Four LED Profile fixture must b

1 Installation and User Interface 25Color MixesThe following table shows the color mixes for the fixture.Terminology:• White Point - The color tempera

26 Source Four LED Profile v1.6.0 User ManualRGBEffectively addresses all seven colors via three channels of control. The RGB profile produces medium-

1 Installation and User Interface 27StrobeIn most profiles, strobe is assigned to channel 5. It adds another channel to any of the DMX profiles. Under

28 Source Four LED Profile v1.6.0 User ManualDaylight and Tungsten ProfilesDirect ControlThe first DMX channel always controls Intensity from 0 to 100

1 Installation and User Interface 29DMX Footprints and Channel MappingTungsten and DaylightLustr+, Series 2 Lustr, and Studio HD* When this feature is

30 Source Four LED Profile v1.6.0 User ManualInstalling AccessoriesColor Frame HolderFigure-1.14 Color frame holder and retaining clip.The gel frame h

2 Basic Menu Navigation 31Chapter 2Basic Menu NavigationThis chapter contains the following sections:• User Interface Overview . . . . . . . . . . . .

32 Source Four LED Profile v1.6.0 User ManualUser Interface OverviewThe Source Four LED Profile user interface (UI) consists of an LCD and keypad. All

2 Basic Menu Navigation 33KeypadUse the keypad buttons to access and navigate the menus on the LCD. Figure-2.2 Keypad buttons.Keypad LockoutThe keypad

ii Source Four LED Profile v1.6.0 User ManualIndicator Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23DMX Profil

34 Source Four LED Profile v1.6.0 User ManualStatus IndicatorsFigure-2.3 Status Indicators on the back of the fixture.The status indicators are three,

2 Basic Menu Navigation 35Status (Home) ScreensThe status (home) screens display when you press [] or when there is no activity for a specific time, w

36 Source Four LED Profile v1.6.0 User ManualSystem Message AreaDisplays status messages, which vary depending on the function that is currently activ

3 Operation 37Chapter 3OperationThis chapter contains the following sections:• Home Screen Displays . . . . . . . . . . . . . . . . . . . . . . . . .

38 Source Four LED Profile v1.6.0 User ManualHome Screen DisplaysDepending on the fixture settings, the following are displayed in the system message

3 Operation 39Fan ControlThe fan can be forced on via DMX control or by adjusting settings under the Advanced Settings menu. For more information, see

40 Source Four LED Profile v1.6.0 User ManualMain MenuThe Main Menu can be accessed at any time while viewing other screens. To access the Main Menu,

3 Operation 41Advanced SettingsThe Advanced Settings menu is for experienced users or for applications that entail very carefully defined performance

42 Source Four LED Profile v1.6.0 User ManualAdvanced MenuThe Advanced Menu provides access to various fixture settings and specific operations. The A

3 Operation 43DMX ProfileThe current DMX profile is displayed on the DMX Settings menu. You can customize the setting by selecting a different profile

iiiAppendix AQuick Start . . . . . . . . . . . . . . . . . . . . . . . . . 77Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

44 Source Four LED Profile v1.6.0 User ManualFan ControlFan Control adds another DMX channel of control when set to DMX. Alternate settings are Slow,

3 Operation 45Plus Seven (Lustr+, Series 2 Lustr, and Studio HD)Plus Seven allows enhanced color-mixing precision when using the RGB, HSI, HSIC, or St

46 Source Four LED Profile v1.6.0 User ManualLED SettingsUse the LED Settings menu to adjust fixture performance. From the LED Settings menu, you can

3 Operation 47Step 1: On the Advanced Menu, scroll to LED Settings.Step 2: Press [].Step 3: With Output selected, press [] to toggle between the optio

48 Source Four LED Profile v1.6.0 User ManualLinearLinear has no curve. Brightness levels correlate exactly with the value of the dimming control sign

3 Operation 49Output FreqOutput Frequency is the frequency in Hz at which the LED array pulses, or blinks, as a function of Pulse-Width Modulation (PW

50 Source Four LED Profile v1.6.0 User ManualWhite Point (Lustr+, Series 2 Lustr, and Studio HD)White Point controls the appearance (color temperature

3 Operation 51Presets (Lustr+, Series 2 Lustr, and Studio HD)A Preset is a single, static look or color mix. The Source Four LED Profile fixture comes

52 Source Four LED Profile v1.6.0 User ManualStep 1: On the Presets and Sequences menu, scroll to Presets. Step 2: Press [].Step 3: With Preset select

3 Operation 53Figure-3.18 Selecting Delay Time on the Presets Menu.Step 2: Press [] or [] to set the desired time in minutes.Step 3: Press [].Step 4:

iv Source Four LED Profile v1.6.0 User Manual

54 Source Four LED Profile v1.6.0 User ManualEdit (Daylight and Tungsten)Use Edit to change the brightness and strobe settings of the LED array. To ke

3 Operation 55Save DMX as PresetYou can take a snapshot of the incoming DMX signal when the fixture is in HSI mode and save it as a preset value.Step

56 Source Four LED Profile v1.6.0 User ManualSequencesA Sequence is a timed series of presets. Up to 12 different Sequences may be altered for Preset

3 Operation 57Step 1: On the Sequences menu, scroll to Rate and press []. Figure-3.24 Selecting Rate on the Sequences Menu.Step 2: Press [] or [] to s

58 Source Four LED Profile v1.6.0 User ManualPresetPreset is the number of a Preset, whether it is a predefined or a custom color mix. Step 1: On the

3 Operation 59BounceOnce the fixture completes the entire sequence, it reverses the order of the presets and steps backward through them until reachin

60 Source Four LED Profile v1.6.0 User ManualQuick Color (Lustr+, Series 2 Lustr, Studio HD)Quick Color allows you to easily select a color and its in

3 Operation 61When operating as the Master fixture, the fixture displays Master on its home screen.Figure-3.30 XYZ Status Screen Showing Master.SlaveA

62 Source Four LED Profile v1.6.0 User ManualStep 1: On the Diagnostics screen, scroll to Current DMX In.Step 2: Press [].Figure-3.32 Current DMX In S

3 Operation 63TestTest is used to test the fixture and display its output values. Test overrides all other control to the fixture. The action options

Introduction 1IntroductionCongratulations on your purchase of a Source Four LED Profile by ETC product.Source Four LED Profile’s x7 Color System™ seve

64 Source Four LED Profile v1.6.0 User ManualIndividual Control (Ind Cntl)Use Individual Control to select each LED series and then adjust its intensi

3 Operation 65Recalibrate FixtureService technicians may use this option to calibrate the constant current driver electronics for the LEDs. The calibr

66 Source Four LED Profile v1.6.0 User ManualLocal SettingsThe Local Settings menu gives you several options that affect the LCD and other functions o

3 Operation 67LanguageEnglish is used for all menus. No other languages are offered at this time.Figure-3.40 Setting the Screen Language.Status Indica

68 Source Four LED Profile v1.6.0 User ManualOverTemp You can change how an over-temperature situation is indicated in order to control stray light. V

3 Operation 69Copy All SettingsWhen DMX is not applied you can copy all, except DMX address, settings globally to all of the other fixtures in the sam

70 Source Four LED Profile v1.6.0 User ManualStudio SettingsLustr+, Series 2 Lustr, and Studio HDThe Studio profile produces only white light that is

3 Operation 71Studio DMX ControlWhen controlled via DMX, the first three channels adjust the output in the following order. Channel 5 controls strobe.

72 Source Four LED Profile v1.6.0 User ManualDaylight and TungstenThe Studio profile allows quick adjustment of Intensity. The Studio profile can be o

3 Operation 73Error MessagesWhen a system error is detected, a message displays on the home screen. The message changes to reflect the specific error

2 Source Four LED Profile v1.6.0 User ManualDaylight and TungstenOptions include:• Multiple dimming curve options.• Presets and sequences for standalo

74 Source Four LED Profile v1.6.0 User ManualSoftware UpdatesThe software can be updated with UpdatorAtor Software. UpdatorAtor allows you to remotely

3 Operation 75Routine MaintenanceTo ensure optimum performance of your Source Four LED Profile fixture, you should perform the following inspections a

76 Source Four LED Profile v1.6.0 User ManualInspecting and Cleaning the ElectronicsA can of compressed air or oil-free air from an air compressor s

Quick Start 77Appendix AQuick StartThis section will help users to quickly use the Source Four LED fixture. For complete, detailed information and ste

78 Source Four LED Profile v1.6.0 User ManualConfigureSet DMX AddressStep 1: From the main screen, press [] to open the Main Menu.Step 2: On the Main

Quick Start 79Quick Setups MenuVarious pre-programmed combinations of operational settings are available to quickly get you started. These settings ar

80 Source Four LED Profile v1.6.0 User ManualQuick Setups (Daylight and Tungsten)Step 1: On the Main Menu, scroll to Quick Setups.Step 2: Press [].Ste

B Menu Flow Chart 81Appendix BMenu Flow ChartThe following illustrations show each of the menus that are displayed on the Source Four LED fixture LCD

82 Source Four LED Profile v1.6.0 User ManualHome and Main Menus (Daylight and Tungsten)To Advanced MenuMain MenuDMX Start Address: 001Quick SetupsAd

B Menu Flow Chart 83Advanced Menu (Lustr+, Series 2 Lustr, and Studio HD)Advanced MenuDMX SettingsLED SettingsPresets and SequencesDiagnosticsLocal Se

Introduction 3Fixture ComponentsFigure-1.1 Components of the Source Four LED Profile Fixture.Figure-1.2 Components of the Rear Panel.Figure-1.3 Keypad

84 Source Four LED Profile v1.6.0 User ManualAdvanced Menu (Daylight and Tungsten)Advanced MenuDMX SettingsLED SettingsPresets and SequencesDiagnostic

B Menu Flow Chart 85Presets Menu (Lustr+, Series 2 Lustr, and Studio HD)Presets and SequencesFocus: OffPresetsSequencesQuick ColorPreset 1 is ActiveNo

86 Source Four LED Profile v1.6.0 User ManualPresets Menu (Daylight and Tungsten)Presets and SequencesFocus: OffPresetsSequencesPreset 1 is ActiveNo S

B Menu Flow Chart 87Sequences Menu (all fixture types) and Quick Color Menu (Lustr+, Series 2 Lustr, and Studio HD only)If Preset is set to ‘0’Sequenc

88 Source Four LED Profile v1.6.0 User ManualDiagnostics MenuAbout FixtureRDM: 6574:12345678Ver: 1.4.1.0.0.20 (1)Ser: 000021xxxDesire Vivid 22DMX STAR

B Menu Flow Chart 89Diagnostics TestAdvanced MenuDMX SettingsLED SettingsPresets and SequencesDiagnosticsLocal SettingsDiagnosticsCurrent DMX InNetwor

90 Source Four LED Profile v1.6.0 User ManualDiagnostics Recalibrate FixtureAdvanced MenuDMX SettingsLED SettingsPresets and SequencesDiagnosticsLocal

B Menu Flow Chart 91

92 Source Four LED Profile v1.6.0 User Manual