ETC Source Four LED Series Manuel d'utilisateur Page 37
- Page / 96
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
1 Installation and User Interface Overview 32
Plus 7
Plus 7 adds precision color-control channels to the HSI, HSIC, RGB, and Studio profiles.
For example, HSI with Plus 7 enabled becomes a 15-channel profile. Placing channel 7 at
a value over 51% activates the 15-channel profile within the fixture. The desired color and
intensity is achieved by using the HSI or RGB channels as a starting point. Channels 8 to
14 represent the native LED colors of the fixture and allow you to adjust each color up or
down in order to fine-tune the overall color output.
Color Matching
The color output of all Source Four LED series fixtures is calibrated at the factory. When
operating in the RGB, HSI, HSIC, or Studio profile, each fixture makes accommodations for
the specific LEDs in its array and produces output that is consistent with other fixtures,
whether or not they utilize LEDs from the same production batch. Operating in the Direct
Control profile or with Plus 7 settings adjustments bypasses this calibration and multiple
fixtures may produce slightly different outputs when controlled as a group.
Note:
Depending on the initial color mix, some LED colors may begin at full intensity.
Moving the individual control channels for these colors from 128 to 255 will produce
no effective change from the initial color mix. Conversely, some LED colors may
begin at zero intensity, and moving individual control channels from 128 to 0 will
produce no change.
Data Channel Control Value Function
8 Fixture address + 7 Plus 7 control
0 to 129 = Plus 7 disabled
130 to 255 = Plus 7 enabled
Disable or enable Plus 7
control
9 Fixture address + 8
Color 1
a
a) See Color Mixes, page 30.
128 = No change from initial color
mix
129-255 = Increase from starting
value to full intensity
127-0 = Decrease from starting
value to zero intensity
Alter the individual LED
colors within the array to a
maximum of full intensity
or a minimum of zero
intensity.
10 Fixture address + 9
Color 2
a
11 Fixture address + 10
Color 3
a
12 Fixture address + 12
Color 4
a
13 Fixture address + 13
Color 5
a
14 Fixture address + 14
Color 6
a
15 Fixture address + 15
Color 7
a
- User Manual 1
- Table of Contents 3
- Introduction 6
- Daylight and Tungsten 7
- Fixture Components 8
- Introduction 4 9
- Applications 10
- Document Conventions 10
- WARNING: 11
- Contacts 12
- Quick Start 13
- Configure 14
- Soft Focus Diffuser 14
- Quick Setups Menu 15
- Studio Quick Setup 16
- Advanced Settings 16
- Overview 17
- Specifications 18
- Typical Power Consumption 19
- Note About LED Fixtures 19
- Hardware 21
- Install Lens Tube 22
- Aim Adjustments 23
- Focusing the Beam 24
- Shaping the Beam 24
- Accessory Slot 26
- CAUTION: 27
- Adjusting the Yoke Position 28
- Installation Clearances 29
- Safety Cable 31
- Fixture Weight 31
- Connections 33
- DMX Profile 34
- Color Mixes 35
- Color Matching 37
- Direct Control 38
- Fan Control 38
- Tungsten and Daylight 39
- Lustr+ and Studio HD 39
- Installing Accessories 40
- Basic Menu Navigation 41
- User Interface Overview 42
- 2 Basic Menu Navigation 38 43
- Keypad Lockout 43
- Lustr+ screen shown 44
- Display Title 45
- Input Settings 45
- DMX Address 45
- Menu Navigation 46
- Operation 47
- Home Screen Displays 48
- 3 Operation 44 49
- Main Menu 50
- Operation 46 51
- Advanced Menu 52
- Data Loss 54
- HLL-2Min 54
- HLL-4ever 54
- Using Plus Seven Control 55
- Regulated 56
- Protected 56
- Standard 57
- Incandescent 57
- Output Freq 59
- Red Shift 59
- 3 Operation 56 61
- Fade Time 62
- Delay Time 63
- [Enter]. To discard 63
- Edit (Daylight and Tungsten) 64
- Copy to Other Fixtures 64
- Save DMX as Preset 64
- Sequences 65
- Link Time 67
- Finishing the Sequence 68
- Master/Slave Operation 69
- Current DMX In 70
- Network Statistics 71
- Individual Control (Ind Cntl) 72
- Recalibrate Fixture 73
- About Fixture 73
- Backlight 74
- BLght time out 74
- Language 75
- Status Indicators 75
- Operation 72 77
- Studio Settings 78
- 3 Operation 74 79
- Studio DMX Control 80
- Error Messages 81
- Software Updates 82
- Routine Maintenance 83
- Appendix A 86
- Menu Flow Chart 86
- System OK 87
- Menu Flow Chart 84 89
- To Sequences 90
- Status: Active 92
- To Recalibrate 93
- To Te s t 93
- Menu Flow Chart 90 95
Produits connexes et manuels pour Lumières des projecteurs ETC Source Four LED Series
(8 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.911 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels