ETC Source Four LED Series Manuel d'utilisateur Page 56
- Page / 96
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
51 Source Four LED Profile v1.4.0 User Manual
NOTE:
Once any one of the seven individual color channels is altered from its neutral starting
position, the settings for the original color point may no longer reflect the actual output of
the fixture.
When using RGB, HSI, HSIC, or Studio profile for color selection, each fixture makes
accommodations for the specific LEDs in its array and produces output that is consistent
with other fixtures, whether or not they use LEDs from the same production batch.
Operating with Plus Seven enabled can override this calibration, and multiple fixtures
may produce slightly different outputs when individual color channels are altered from
their neutral starting points.
LED Settings
Use the LED Settings menu to adjust fixture performance. From the LED Settings menu,
you can set the following.
• Output
•Curve
• Output Frequency
•Red Shift
• White Point
Figure-3.10 Selecting LED Settings on the Advanced Menu.
Output
Use Output to choose the optimal balance between two competing performance
parameters, maximum brightness and output consistency, by adjusting:
• How much the fixture limits the overall power to the LED array.
• How the fixture reduces output as internal fixture components heat up during use or in
high ambient temperatures.
The output options are as follows.
Regulated
Regulated is a moderately constrained power or brightness with consistent output under
typical use. Power to the LEDs is separately regulated in order to maintain consistent
brightness during the initial fixture warm-up period. This is recommended for most indoor
applications.
Protected
Protected provides the most consistent output possible with the greatest potential for
reduced overall brightness. This is best for outdoor use, changing environmental
temperatures, and applications with high requirements for consistency in extreme operating
conditions.
LED Settings
Output: Regulated
Curve: Standard
Output Freq: 1200
Red Shift: Off
White Point: 3200K
Advanced Menu
DMX Settings
LED Settings
Presets and Sequences
Diagnostics
Local Settings
Copy All Settings
- User Manual 1
- Table of Contents 3
- Introduction 6
- Daylight and Tungsten 7
- Fixture Components 8
- Introduction 4 9
- Applications 10
- Document Conventions 10
- WARNING: 11
- Contacts 12
- Quick Start 13
- Configure 14
- Soft Focus Diffuser 14
- Quick Setups Menu 15
- Studio Quick Setup 16
- Advanced Settings 16
- Overview 17
- Specifications 18
- Typical Power Consumption 19
- Note About LED Fixtures 19
- Hardware 21
- Install Lens Tube 22
- Aim Adjustments 23
- Focusing the Beam 24
- Shaping the Beam 24
- Accessory Slot 26
- CAUTION: 27
- Adjusting the Yoke Position 28
- Installation Clearances 29
- Safety Cable 31
- Fixture Weight 31
- Connections 33
- DMX Profile 34
- Color Mixes 35
- Color Matching 37
- Direct Control 38
- Fan Control 38
- Tungsten and Daylight 39
- Lustr+ and Studio HD 39
- Installing Accessories 40
- Basic Menu Navigation 41
- User Interface Overview 42
- 2 Basic Menu Navigation 38 43
- Keypad Lockout 43
- Lustr+ screen shown 44
- Display Title 45
- Input Settings 45
- DMX Address 45
- Menu Navigation 46
- Operation 47
- Home Screen Displays 48
- 3 Operation 44 49
- Main Menu 50
- Operation 46 51
- Advanced Menu 52
- Data Loss 54
- HLL-2Min 54
- HLL-4ever 54
- Using Plus Seven Control 55
- Regulated 56
- Protected 56
- Standard 57
- Incandescent 57
- Output Freq 59
- Red Shift 59
- 3 Operation 56 61
- Fade Time 62
- Delay Time 63
- [Enter]. To discard 63
- Edit (Daylight and Tungsten) 64
- Copy to Other Fixtures 64
- Save DMX as Preset 64
- Sequences 65
- Link Time 67
- Finishing the Sequence 68
- Master/Slave Operation 69
- Current DMX In 70
- Network Statistics 71
- Individual Control (Ind Cntl) 72
- Recalibrate Fixture 73
- About Fixture 73
- Backlight 74
- BLght time out 74
- Language 75
- Status Indicators 75
- Operation 72 77
- Studio Settings 78
- 3 Operation 74 79
- Studio DMX Control 80
- Error Messages 81
- Software Updates 82
- Routine Maintenance 83
- Appendix A 86
- Menu Flow Chart 86
- System OK 87
- Menu Flow Chart 84 89
- To Sequences 90
- Status: Active 92
- To Recalibrate 93
- To Te s t 93
- Menu Flow Chart 90 95
Produits connexes et manuels pour Lumières des projecteurs ETC Source Four LED Series
(8 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.130 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels