ETC Source Four LED Series Manuel d'utilisateur Page 69
- Page / 96
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
3 Operation 64
Copy to Other Fixtures
If other fixtures are connected to the same data chain, you can copy the Sequences
settings to the other fixtures. The fixture automatically becomes the Master and controls all
the other fixtures (Slaves) in the chain until another fixture has its Preset or Sequence
settings selected or activated. For more information, see Master/Slave Operation, page 64.
Step 1: On the Sequences screen, scroll to Copy to Other Fixtures.
Figure-3.28 Selecting Copy to Other Fixtures.
Step 2: Press [Enter].
Step 3: When asked if you are sure, select Yes and press [Enter].
Master/Slave Operation
When similar fixtures' DMX or data connections are linked together and there is no external
DMX signal going to them, one fixture automatically controls all other fixtures in the chain
when a Preset or Sequence is initiated.
Master
Master is the one fixture that controls all fixtures in the daisy chain. By default, it is
whichever fixture had its Preset or Sequence selected or adjusted most recently. The
Master fixture can only control Slave fixtures to produce identical output at the same time
as itself. The Master fixture cannot control Slave fixtures to operate individually or to run
chase-type or time-offset sequences.
Changes and edits to Presets or Sequences that are made to the Master fixture may be
copied to the internal memory of all Slave fixtures for later use when these fixtures are
disconnected from the data daisy chain.
When operating as the Master fixture, the fixture displays Master on its home screen.
Figure-3.29 XYZ Status Screen Showing Master.
Note:
This option only copies Sequence data; it does not copy changes to the Preset
settings or color mixes used within the Sequence.
Sequences
Sequence: * 3
Status: Active
Rate: 100%
Step: 01
Preset: 0
End State: Loop
Copy to Other Fixture
Studio
Master
Preset 1 is Active
System OK
No Sequence is Active
Studio Prt Lin –– Str
1/5 In te n s it y
- User Manual 1
- Table of Contents 3
- Introduction 6
- Daylight and Tungsten 7
- Fixture Components 8
- Introduction 4 9
- Applications 10
- Document Conventions 10
- WARNING: 11
- Contacts 12
- Quick Start 13
- Configure 14
- Soft Focus Diffuser 14
- Quick Setups Menu 15
- Studio Quick Setup 16
- Advanced Settings 16
- Overview 17
- Specifications 18
- Typical Power Consumption 19
- Note About LED Fixtures 19
- Hardware 21
- Install Lens Tube 22
- Aim Adjustments 23
- Focusing the Beam 24
- Shaping the Beam 24
- Accessory Slot 26
- CAUTION: 27
- Adjusting the Yoke Position 28
- Installation Clearances 29
- Safety Cable 31
- Fixture Weight 31
- Connections 33
- DMX Profile 34
- Color Mixes 35
- Color Matching 37
- Direct Control 38
- Fan Control 38
- Tungsten and Daylight 39
- Lustr+ and Studio HD 39
- Installing Accessories 40
- Basic Menu Navigation 41
- User Interface Overview 42
- 2 Basic Menu Navigation 38 43
- Keypad Lockout 43
- Lustr+ screen shown 44
- Display Title 45
- Input Settings 45
- DMX Address 45
- Menu Navigation 46
- Operation 47
- Home Screen Displays 48
- 3 Operation 44 49
- Main Menu 50
- Operation 46 51
- Advanced Menu 52
- Data Loss 54
- HLL-2Min 54
- HLL-4ever 54
- Using Plus Seven Control 55
- Regulated 56
- Protected 56
- Standard 57
- Incandescent 57
- Output Freq 59
- Red Shift 59
- 3 Operation 56 61
- Fade Time 62
- Delay Time 63
- [Enter]. To discard 63
- Edit (Daylight and Tungsten) 64
- Copy to Other Fixtures 64
- Save DMX as Preset 64
- Sequences 65
- Link Time 67
- Finishing the Sequence 68
- Master/Slave Operation 69
- Current DMX In 70
- Network Statistics 71
- Individual Control (Ind Cntl) 72
- Recalibrate Fixture 73
- About Fixture 73
- Backlight 74
- BLght time out 74
- Language 75
- Status Indicators 75
- Operation 72 77
- Studio Settings 78
- 3 Operation 74 79
- Studio DMX Control 80
- Error Messages 81
- Software Updates 82
- Routine Maintenance 83
- Appendix A 86
- Menu Flow Chart 86
- System OK 87
- Menu Flow Chart 84 89
- To Sequences 90
- Status: Active 92
- To Recalibrate 93
- To Te s t 93
- Menu Flow Chart 90 95
Produits connexes et manuels pour Lumières des projecteurs ETC Source Four LED Series
(8 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.090 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels