ETC Source Four LED Series Manuel d'utilisateur Page 73
- Page / 96
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
3 Operation 68
Recalibrate Fixture
Service technicians may use this option to calibrate the constant current driver electronics
for the LEDs. The calibration process goes through each series of LEDs, starting at 0
intensity and stepping up to 100%. The calibration is automatic and takes a few minutes.
During this time, do not exit the screen until it is complete.
Step 1: On the Diagnostics screen, scroll to ReCalibrate Fixture.
Step 2: Press [Enter].
Step 3: When asked if you are sure, select Yes and press [Enter].
A new screen shows that the calibration is in progress and whether the LEDs
pass the calibration.
Figure-3.35 LED Calibration Screen with Calibration in Process.
Step 4: Press [Enter] or [Back] to return to the Diagnostics screen.
About Fixture
The About screen displays the following information. This is a read-only screen.
• The software version number
• The fixture serial number
• The assigned fixture RDM number
• The color bias of the LED array
Figure-3.36 About Fixture screen.
Step 1: On the Diagnostics screen, scroll to About Fixture.
Step 2: Press [Enter].
Step 3: Press [Enter] or [Back] to return to the Diagnostics screen.
CAUTION:
This calibration process does not measure or recalibrate the light output of the LEDs.
Under normal use, it is not necessary to recalibrate the fixture, and doing so will likely
have no beneficial effect on fixture performance. It is therefore NOT recommended
to recalibrate the fixture without express instruction from an authorized technician.
LED Calibration
LED 1 .......Pass
LED 2 .......Pass
LED 3 .......Pass
LED 4 .......Working
LED 5 .......Working
LED 6 .......Working
LED 7 .......Working
Diagnostics
Recalibrate Fixture
This Will Calibrate
LED Array
Are You Sure?
Yes
No
About Fixture
RDM: 9827582
Ver: 1.0.0.0.9.001
Ser: 0782xxxx
Red Range — 40
- User Manual 1
- Table of Contents 3
- Introduction 6
- Daylight and Tungsten 7
- Fixture Components 8
- Introduction 4 9
- Applications 10
- Document Conventions 10
- WARNING: 11
- Contacts 12
- Quick Start 13
- Configure 14
- Soft Focus Diffuser 14
- Quick Setups Menu 15
- Studio Quick Setup 16
- Advanced Settings 16
- Overview 17
- Specifications 18
- Typical Power Consumption 19
- Note About LED Fixtures 19
- Hardware 21
- Install Lens Tube 22
- Aim Adjustments 23
- Focusing the Beam 24
- Shaping the Beam 24
- Accessory Slot 26
- CAUTION: 27
- Adjusting the Yoke Position 28
- Installation Clearances 29
- Safety Cable 31
- Fixture Weight 31
- Connections 33
- DMX Profile 34
- Color Mixes 35
- Color Matching 37
- Direct Control 38
- Fan Control 38
- Tungsten and Daylight 39
- Lustr+ and Studio HD 39
- Installing Accessories 40
- Basic Menu Navigation 41
- User Interface Overview 42
- 2 Basic Menu Navigation 38 43
- Keypad Lockout 43
- Lustr+ screen shown 44
- Display Title 45
- Input Settings 45
- DMX Address 45
- Menu Navigation 46
- Operation 47
- Home Screen Displays 48
- 3 Operation 44 49
- Main Menu 50
- Operation 46 51
- Advanced Menu 52
- Data Loss 54
- HLL-2Min 54
- HLL-4ever 54
- Using Plus Seven Control 55
- Regulated 56
- Protected 56
- Standard 57
- Incandescent 57
- Output Freq 59
- Red Shift 59
- 3 Operation 56 61
- Fade Time 62
- Delay Time 63
- [Enter]. To discard 63
- Edit (Daylight and Tungsten) 64
- Copy to Other Fixtures 64
- Save DMX as Preset 64
- Sequences 65
- Link Time 67
- Finishing the Sequence 68
- Master/Slave Operation 69
- Current DMX In 70
- Network Statistics 71
- Individual Control (Ind Cntl) 72
- Recalibrate Fixture 73
- About Fixture 73
- Backlight 74
- BLght time out 74
- Language 75
- Status Indicators 75
- Operation 72 77
- Studio Settings 78
- 3 Operation 74 79
- Studio DMX Control 80
- Error Messages 81
- Software Updates 82
- Routine Maintenance 83
- Appendix A 86
- Menu Flow Chart 86
- System OK 87
- Menu Flow Chart 84 89
- To Sequences 90
- Status: Active 92
- To Recalibrate 93
- To Te s t 93
- Menu Flow Chart 90 95
Produits connexes et manuels pour Lumières des projecteurs ETC Source Four LED Series
(8 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.672 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels